High quality heavy duty folding table support with soft close damper EB-303-DA made of stainless steel. Folding console up to 100kg load capacity. Flap support from ROCA / Sugatsune

$ 90,99

In stock

Description

High quality heavy duty folding bracket with damper made of stainless steel with load capacity up to 100 kg

blank

Application:

These high quality solid stainless steel folding table supports are best suited for humid and harsh environments and can be used in a variety of ways.

The folding consoles can be used in homes, offices, restaurants, hotels, etc.

One of the possible applications is the work surface extension in the kitchen or table extension.

blank
High quality stainless steel damped folding bracket EB-303-DA with load capacity up to 100 kg. Application folding table

 

Also, they can be perfectly used for the interior of motor homes, caravans, boats, yachts and trains.

The flap supports are designed for hard use environments, but thanks to their classic industrial look they are also perfect for modern interiors.

blank
High quality folding brackets with soft-close EB-303-DA made of stainless steel with load capacity up to 100 kg. Application in a living room

 

These EB-303-DA folding table holders are also very suitable for use in Tiny House or Micro Apartment to flexibly arrange space as needed.

A special feature of these flap brackets is that the flap support and flap hinge are combined in one fitting.

blank
High quality folding brackets with soft-close EB-303-DA made of stainless steel with load capacity up to 100 kg. Application, open and closed state

 

The built-in soft-close damper ensures that the flap closes gently. For lighter flaps, you can install a flap support without dampers.

When the flap is folded, it is locked in place by pressing on the surface if necessary. Thus, the folding table in the caravan or boat remains in the closed position even while driving, does not wobble and does not produce noise.

When the folding table holder is opened, it automatically locks in the upper position and can be loaded.

blank
High quality folding brackets with soft-close EB-303-DA made of stainless steel with load capacity up to 100 kg. Usage

 

To fold the folding table back together, both levers on the left and right must be operated simultaneously. This ensures that the flap support is not accidentally folded.

The release lever of the folding angles is extra long to facilitate gripping.

The folding brackets are made of corrosion-resistant stainless steel.

The surfaces are elaborately finished, so the fittings look very high quality.

Assembly:

blank
High quality folding consoles with soft close EB-303-DA made of stainless steel. Mounted in the kitchen as an extension of the work surface

 

Mounting is done with screws.

The maximum load can be achieved by distributing the load so that the center of gravity is in the middle (
s. Fig.
).

If the center of gravity of the flap is at the edge of the folding table holder, the load capacity is 75 kg.

blank
High quality folding consoles with soft close EB-303-DA made of stainless steel. The load capacity depends on the position of the center of gravity

 

Attention: the wall must be suitable to bear the required load.

The rear wall of the folding brackets is rounded so that they can be mounted not only on straight surfaces but also on tubes (Ø25 mm).

From the
Picture below
you can see when one and when two dampers are needed.

blank
Two EB-303-DA damper supports with soft-close damper or one EB-303-DA and one EB-303 without damper can be installed

 

If the flap is narrow, the flap table holders can alternatively be mounted in reverse.

In this case, the longer side is mounted on the wall and the shorter side is used for the folding table or shelf.

This has no negative effect on the load (
s. Fig.
).

blank
High quality folding consoles with soft close EB-303-DA made of stainless steel. Reverse mounting for narrow flaps

 

Features:

  • Load capacity in the center: 495 N (50 kp) for 1 folding angle
  • Torque: 230 Nm
  • Weight: 500 g
  • Longer release lever
  • Ambient temperature: from -30°C to +120°C
  • Endurance test: 50,000 cycles passed

Included in delivery:

  • 1 piece stainless steel folding table support

Material:

  • Made of high quality stainless steel SUS304 (AISI304, V2A)

Surface:

  • Stainless steel electric polished

Dimensions:

  • Length: 307 mm
  • Height: 165 mm
  • Width: 29 mm
  • Radius back wall: Ø25 mm

For dimensions see technical drawing (mm):

blank
Technical drawing: High quality stainless steel folding brackets with soft-close EB-303-DA

 

Watch product video:

Manufacturer’s reference number:

 

Stainless steel polished: 120-048-775

907260

EB-303-DA, old: EB-303/EP-D

 

Manufacturer: ROCA Industry (Sweden)

Distributors: SUGATSUNE / LAMP® (Japan)

SUGATSUNE, The manufacturer of the brand LAMP®

 

You may also like…